# How to Set Up the XH22 Kit

> For AI tools: this is the Markdown copy of https://xproxy.io/document/getting-started-with-your-xproxy-kit. Every XProxy guide has one at its URL + `.md`; the index of all guides is https://xproxy.io/llms.txt.

Set up the XProxy XH22 mobile proxy kit in about 10 minutes: SIMs, USB hub, XProxy box, router and power, shown step by step in 3D.

Set up your XProxy XH22 Kit in 7 steps, about 10 minutes from the box to working mobile proxies. Each step plays in 3D: drag to look from any side.

**You need:** the kit, one micro SIM with mobile data per dongle, and a router with internet and a free LAN port.

## Set it up

**Step 1: Meet your kit**

Everything on one desk: the XProxy box, the USB hub, the XH22 dongles and their cables.

**In the box:** XProxy box with its 5 V adapter, USB hub with its USB cable and 12 V adapter, network cable, dongles.

**You provide:** a router that is online and a power strip with two free sockets.

> You also need one micro SIM with mobile data for each dongle.

**Step 2: Put a SIM in each dongle**

Turn the dongle over and slide the SIM cover off toward its tail.

Lay a micro SIM in, gold contacts down, and push it all the way in.

Slide the cover back on toward the USB end. Do the same for every dongle.

> Use data SIMs with an active plan. Only put SIMs in or take them out while the hub is off.

**Step 3: Plug the dongles into the hub**

Plug the dongles in by their number labels, one port after another: front row first, USB end down, pressed straight in.

Then the back row. Press each one all the way in.

> **Keep the number labels on.** They match the dongle numbers in your dashboard, so you can find any dongle on the hub at a glance.

**Step 4: Connect the hub to the XProxy box**

USB cable: the square end goes into the hub, the flat end into a USB port on the XProxy box.

> Either USB port on the XProxy box works.

**Step 5: Connect the XProxy box to your router**

Plug the network cable into a free LAN port on your router.

Plug the other end into the XProxy box.

> Your router must already be online.

**Step 6: Power everything on**

Plug the 12 V adapter into your power strip.

Plug its round plug into the hub.

Switch the hub ON. The hub's light and every dongle's light come on.

Plug the XProxy box's 5 V adapter into the power strip.

Plug its round plug into the XProxy box.

> **Do not mix up the two adapters.** They have the same plug, but the 12 V one is for the hub only and can damage the XProxy box.

**Step 7: Check the lights**

Within a minute, the hub's power light is on and every dongle's light blinks.

The XProxy box shows its address on its display, for example **192.168.1.86**. Type it into a browser on the same network to open your dashboard.

Done: your dongles are ready to become proxies.

> **Your kit is ready.** Next, [open your XProxy dashboard](https://xproxy.io/document/how-access-dashboard-xproxy), then [activate your license](https://xproxy.io/document/how-active-upgrade-license).

**Setup checklist**

- **Unpack:** XProxy box, USB hub, dongles, cables and the two adapters.
- **SIMs:** one micro SIM in each dongle, gold contacts down.
- **Dongles:** into the hub by their number labels.
- **Hub to box:** USB cable, square end in the hub.
- **Box to router:** network cable into a free LAN port.
- **Power:** 12 V adapter to the hub, switch ON, then 5 V adapter to the box.
- **Check:** dongle lights blink, the box shows its IP address. Open it in your browser.

## Something not working?

| You see | What to do |
| --- | --- |
| No light on the hub | Check the 12 V adapter is plugged in and the hub is switched on. |
| One dongle light stays off | Push the dongle all the way into the hub, or try another port. |
| The green light on the hub is off | Check the USB cable at both ends: hub and XProxy box. |
| No address on the XProxy box | Check its 5 V adapter and the network cable at both ends, and that your router is online. |

---

Source: https://xproxy.io/document/getting-started-with-your-xproxy-kit
